The field of this invention is throttling valves and more particularly those used on centrifugal compressors to match output to system demands.
Centrifugal compressors are frequently packaged in multiple stages using a common drive including associated controls. One type of control involved throttling the suction to the initial stage so as to match the output of the compressor to the system demands. Doing this avoids the cost of energy to power the compressor units at output levels not required from the system. The nature of the performance curve of centrifugal compressors is that their output flow and pressure are related and can be varied by a throttling assembly typically mounted at the suction to the first stage. These throttling assemblies have been designed in the past using a series of blades that rotate 90 degrees between the open and closed position. Typically each blade has a pair of end shafts that extend out of the inlet piping going to the first stage. Each such shaft extension through the piping system was provided with a shaft seal and a purge system. The purpose of the purge system was to keep gasses from escaping these shaft seals particularly in applications where inlet pressures in a particular system ran normally at elevated pressures that were raised to an even higher pressure by the compressor system. The purge system served a purpose of avoiding sucking in surrounding air in some systems. In conditions of high turndown when the blades are operating close to the fully closed position, it was possible for the compressor to draw the pressure down to negative values. In those cases, in order to avoid drawing air into the process gas being compressed, the process gas was hooked to the purge system. If a negative pressure situation occurred, the process gas would be sucked in around shaft seals located at each end of each blade. Depending on the inlet piping size, there could be several blades rotating in tandem with each one having a connection to the purge system.
The blades each had a dedicated linkage typically connected to a rotating ring that was turned by an actuator, typically operated by pneumatic pressure.
The problems with the prior design were numerous. As mentioned above there was the concern of leakage at every shaft seal of every blade and the need to hook up a purge system to each potentially leaking seal. The present invention eliminates the concerns of the previous designs by enclosing the inlet pipe with the blades inside in a surrounding housing. In this approach the leakage at blade shaft seals becomes irrelevant as a surrounding housing contains the process gas. The design further extends a balanced driving piston that is powered by the external pneumatic actuator into the interior of the housing. Balancing the piston reduces actuator output requirements be eliminating internal housing pressure as a load on the drive stem. Multiple seals are available on the drive stem penetrations of the housing to further enhance reliable operation. One or more internal passages remain open between the upstream and downstream sections of the housing on either side of the blades. Thus, when high turndowns with nearly closed blades bring the downstream pressure down to negative values due to continuing compressor operation, the passages serve an equalization function to avoid sucking air into the housing. These and other features of the present invention will be more readily understood from a review of the description and drawings of the preferred embodiment and the claims, which appear below.
A throttling valve assembly has an outer housing that is sealed. An actuator is connected to a pressure balanced shaft that extends into the housing to operate a plurality of linkages that can rotate blades in tandem. With the surrounding housing sealed, the shaft penetrations of the blade support shafts no longer need seals or a purge system to supply process gas during times of reduced pressure in situations with the blades nearly closed. A pressure equalization system has balance passages internal to the housing to allow flow from higher pressure zones to lower pressure zone of the process gas so as to avoid creation of a condition that can draw air into any zones of reduced pressure in the housing.
Referring to
Connector 44 is engaged to an arm 62 that extends radially from ring 64. Translation of connector 44 results in rotation of ring 64. Each blade 66 shown in
The extensions of shafts 76 through inner housing 12 are no longer needed to be sealed as in the prior art. This is because there is an outer housing 16 that has its orifices sealed with flange 20, plug 28 and plug 50.
An annular space 78 is created between outer housing 16 and inner housing 12. Outer housing 16 has an upstream inlet 80 that leads to the blades 66 in the inner housing 12. Pressure in inlet 80 communicates through passage 82 into the annular space 78. That way when the blades 66 go toward the closed position reducing the pressure in the inner housing 12 near flange 10 gasses from annular space 78 flows around shafts 76 so that outside air is not drawn into the inner housing 12. Passage 84 is provided and can be blanked off on outer housing 16. Alternatively, a purge system that can deliver process gas into annular space 78 may still be wanted by some users and they can use passage 84 for that very purpose.
Those skilled in the art will appreciate that the pressure balanced design of upper rod 38 and lower rod 46 makes the driving assembly insensitive to annular space 78 pressure. The redundancy of seals such as 40 and 42 means more hours of reliable operation and less downtime. The pressure balanced design allows the use of a smaller actuator connected to upper rod 38. The pressure equalizing system has no moving parts and equalizes pressure differentials induced by reorientation of the blades 66 fairly fast. The design eliminates shaft seals on the rotating blade or blades 66. The two piece design of the outer housing 16 facilitates maintenance and assembly operations. Seals on rods 38 and 46 can be changed without taking the housing 16 out of the suction piping system to the compressor. Thrust loads on the shafts 76 are reduced if not eliminated since annular space 78 and inner housing 12 quickly equalize to a common pressure upstream of the blades 66.
While the preferred embodiment has been set forth above, those skilled in art will appreciate that the scope of the invention is significantly broader and as outlined in the claims which appear below.
This application is a continuation of U.S. patent application Ser. No. 12/534,822, filed on Aug. 3, 2009, issued as U.S. Pat. No. 7,637,282 on Dec. 29, 2009, and entitled “Compressor Throttling Valve Assembly”, which is herein incorporated by reference in its entirety, and which is a continuation of U.S. patent application Ser. No. 11/200,613, filed on Aug. 10, 2005, issued as U.S. Pat. No. 7,568,503 on Aug. 4, 2009, and entitled “Compressor Throttling Valve Assembly,” which is herein incorporated by reference in its entirety.
Number | Date | Country | |
---|---|---|---|
Parent | 12534822 | Aug 2009 | US |
Child | 12643262 | US | |
Parent | 11200613 | Aug 2005 | US |
Child | 12534822 | US |